Skip to main content
Cisco Meraki Documentation

Client VPN Overview

Client VPN

The client VPN service uses the Layer 2 Tunneling Protocol (L2TP), and can be deployed without any additional software on devices with native support for L2TP VPN connections. Linux-based operating systems might require third-party packages support L2TP/IP VPN connections.

Client VPN uses Triple Data Encryption Standard (3DES) encryption with Secure Hash Algorithm 1 (SHA1) hashing algorithms for Phase1, and Advanced Encryption Standard 128 (AES-128)/3DES encryption with SHA1 hashing algorithms for Phase2. As a best practice, the shared secret, or pre-shared key, should not contain special characters at the beginning or end.

Client VPN connections can only be established on the primary uplink.

Client VPN traffic can be routed through Site-to-Site VPN (both AutoVPN and Non-Meraki VPN).

Learn more with these free online training courses on the Meraki Learning Hub:

Sign in with your Cisco SSO or create a free account to start training.

Configuring MX for Client VPN

To enable client VPN, choose Enabled from the Client VPN server drop-down menu on the Security & SD-WAN > Configure > Client VPN page. The following client VPN options can be configured:

  • Hostname: This is the hostname of the MX that client VPN users will use to connect
    • This hostname is a Dynamic DNS (DDNS) host record correlating to the public IP address of the MX
    • For more information on managing the hostname, see Dynamic DNS (DDNS)
  • Client VPN subnet: The subnet that will be used for client VPN connections
    • This should be a private subnet that is not in use anywhere else in the network
    • The MX will be the default gateway on this subnet and will route traffic to and from this subnet
    • The MX utilizes LCP (Link Control Protocol) to assign IPs to clients, thus DHCP and Static Assignment are not supported
    DNS server: The servers that VPN clients will use to resolve DNS hostnames
  • WINS server: If VPN clients use Windows Internet Name Service (WINS) to resolve NetBIOS names, select Specify WINS Servers from the drop-down and enter the IP addresses of the WINS servers
  • Shared secret: The shared secret, or pre-shared key, that will be used to establish the client VPN connection
  • Authentication: How VPN clients will be authenticated (see Authentication section below)
  • RADIUS timeout: Number of seconds to wait for a response from the RADIUS server before retrying
  • Retry Count: Number of retries before trying the next RADIUS server
  • Systems Manager Sentry VPN security: Configure systems manager to push client VPN configuration settings to enrolled devices (see the Systems Manager Sentry VPN security section and refer to Systems Manager VPN Configurations and Sentry VPN)

Authentication

Meraki client VPN uses the password authentication protocol (PAP) to transmit and authenticate credentials. PAP authentication is always transmitted inside an IPsec tunnel between the client device and the MX security appliance using strong encryption. User credentials are never transmitted in clear text over the WAN or the LAN. 

Client authentication can be performed using: the Meraki cloud, RADIUS, or Active Directory. 

Cisco SecureX Sign-On accounts cannot be used for authentication when using Meraki Cloud Authentication.

Meraki Cloud Authentication

If an Active Directory or RADIUS server is not available, VPN users can be managed with Meraki cloud. Email addresses that are used for Dashboard administrators will automatically populate as Client VPN users, and these administrators will need to log in with their dashboard credentials.

  1. To add or remove additional users, use the User Management section at the bottom of the Security & SD-WAN > Configure > Client VPN page.
  2. Add a user by clicking "Add new user" and entering the following information:
    • Description: Username
    • Email: User email address
    • Password: Enter a password for the user or click "Generate" to automatically generate a password
    • Authorized: Select whether this user is authorized to use the client VPN

To edit an existing user, click on the username in the User Management section.

To delete a user, click the X next to the username on the right side of the user list.

The user email address is the username used for authentication in Meraki Cloud Authentication.

Example of user for client VPN authentication

RADIUS

Use this option to authenticate users on a RADIUS server.

  1. In Security & SD-WAN > Configure > Client VPN click Add a RADIUS server to configure the server(s) to use
  2. In the Host field, enter the IP address of the RADIUS server
  3. In the Port field, enter the port to be used for RADIUS communication
  4. In the Secret field, enter the shared secret for the RADIUS server

For more information on how to configure RADIUS authentication server for client VPN, see Configuring RADIUS Authentication with Client VPN.

If multiple RADIUS servers are configured, RADIUS traffic will not be load-balanced. Server IP addresses are sorted in ascending order from lowest IP to highest IP. RADIUS traffic towards the servers are prioritized in the same manner, starting with the lowest IP address first. This behaviour cannot be modified.

Active Directory

Use this option if user authentication should be done with Active Directory domain credentials.

In Security & SD-WAN > Configure > Active Directory > Active Directory servers, the following information is required for configuration:

  • Short domain: The short name of the Active Directory domain
  • Server IP: The IP address of an Active Directory server on the MX LAN or a remote subnet routable through Auto VPN
  • Domain admin: The domain administrator account the MX should use to query the server
  • Password: The password for the domain administrator account

For more information on how to configure the Active Directory authentication server for client VPN, see Configuring Active Directory with MX Security Appliances.

Security appliances do not support mapping group policies via Active Directory for users connecting through the client VPN.

Systems Manager Sentry VPN Security

When using Meraki Cloud Authentication, Systems Manager Sentry VPN security can be configured if your dashboard organization contains one or more Mobile Device Management (MDM) networks. Systems Manager Sentry VPN security allows for devices enrolled in Systems Manager to receive the configuration to connect to the client VPN through the Systems Manager profile on the device.

To enable Systems Manager Sentry VPN security, go to Security & SD-WAN > Configure > Client VPN > IPsec Settings page. Under the Client VPN Server drop-down menu, select Enabled. You can configure the following options:

  • Install scope: The install scope allows for a selection of Systems Manager tags for a particular MDM network. Devices with these tags applied in a Systems Manager network will receive a configuration to connect to this network's client VPN server through their Systems Manager profile.
    • Send all traffic: Select whether all client traffic should be sent to the MX.
  • Proxy: Whether a proxy should be used for this VPN connection. This can be set to automatic, manual, or disabled.

 

Systems Manager Sentry VPN Security

When using Systems Manager Sentry VPN security, the username and password used to connect to the client VPN are generated by the Meraki cloud.

Usernames are generated based on a hash of a unique identifier on the device and the username of that device. Passwords are randomly generated.

Client VPN Connections

After configuring the client VPN and users starting to connect, it may be useful to see how many and which client devices are connected to your network. To see connected client VPN devices, navigate to Network-wide > Monitor > Clients. Click on the Search drop-down menu and select the following options: Status = Online, offline (or both), Client type = Client VPN

Client VPN Connections View

Group Policies

It is possible to manually apply group policies to clients connected via client VPN. A group policy applied to a client VPN user is associated with the username and not the device. Different devices that connect to client VPN with the same username will receive the same group policy. For more help on assigning or removing group policies applied to a client, refer to the Creating and Applying Group Policies document.

It is not possible to assign group policies automatically once a user connects to client VPN.

Traceroute

The following is expected behavior: When you run a traceroute from a client who is connected to Client VPN to other destinations, one of the hops will appear as IP 192.168.100.1.

 

  • Was this article helpful?